ITALDIAMANT EVOGRES SAW BLADE FOR DEKTON
Made in Italy, the Italdiamant blade features very hard diamond set inside a soft bond for the cutting of ultra compact surfaces.
Producing a fast, clean cut it's the perfect choice for UCS and accredited by the manufacturers of DEKTON and NEOLITH for added peace of mind when cutting these materials.
Remember that you will need a high volume of water when cutting all ultra-compact surfaces with this blade to ensure blade life and product quality.
This is the bridge saw of choice for cutting specialist stones but don’t forget to keep the blade in it’s most efficient condition by sharpening after each cut with our accredited sharpening block
Stonegate Diamond Bridge Saw Blade Technical Parameters - Italdiamant Diamond Bridge Saw Blade For Ultra-Compact Surfaces
...Helping you get the most from your tools!
Water
It's essential that the blade receives the right quantity of water when cutting to refresh and clean the segments.
Italdiamant Blade Technical Parameters
Use our blade RPM matrix below to work out the recommended speed. Simply match the blade diameter and material to the RPM we would recommend for your job:
DEKTON Technical Parameters
| Material Colour | Blade Diameter | Slab Thickness | RPM | Running Speed |
| Dark / Colourful | 350mm | 8 - 12 - 20 - 30mm | 1,900 - 2,500 | 1M / minute |
| White / Light Colours | 350mm | 8 - 12 - 20 - 30mm | 1,900 - 2,500 | 0.5M / minute |
| Dark / Colourful | 400mm | 8 - 12 - 20 - 30mm | 1,700 - 2,300 | 1M / minute |
| White / Light Colours | 450mm | 8 - 12 - 20 - 30mm | 1,700 - 2,300 | 0.5M / minute |
LAPITEC Technical Parameters
| Blade Diameter | Slab Thickness | RPM | Running Speed |
|
350mm |
12mm |
1,900 - 2,500 |
1.5M / minute |
| 20mm | 1M / minute | ||
| 30mm | 0.5M / minute | ||
|
400mm |
12mm |
1,700 - 2,300 |
1.5M / minute |
| 20mm | 1M / minute | ||
| 30mm | 0.5M / minute |
NEOLITH Technical Parameters
| Blade Diameter | Slab Thickness | RPM | Running Speed |
| 350mm | 3 - 6 - 12mm | 1,900 - 2,500 | 1.5M / minute |
| 350mm | 20mm | 1,900 - 2,500 | 1M / minute |
| 400mm | 3 - 6 - 12mm | 1,700 - 2,300 | 1.5M / minute |
| 400mm | 20mm | 1,700 - 2,300 | 1M / minute |
LAMINAM Technical Parameters
| Blade Diameter | Slab Thickness | RPM | Running Speed |
| 350mm | 3 - 3+ - 5 - 7 - 3+3 - 5+3 - 12+ | 1,900 - 2,500 | 1M / minute |
| 400mm | 3 - 3+ - 5 - 7 - 3+3 - 5+3 - 12+ | 1,700 - 2,300 | 1M / minute |
Don't forget! It's recommended that if you're cutting DEKTON & Neolith you keep this Bridge Saw Blade at optimal cutting performance with our Accredited Sharpening Block. It's the best way to ensure neat, chip-free cutting when using this blade on very dense materials. You can find the block at the bottom of this page...
